Looking for:
Kymco agility 125 manual download |
- Kymco agility 125 manual download
There are also frequently asked questions, a product rating and feedback from users to enable you to optimally use your product. If this is not the manual you want, please contact us. Is your product defective and the manual offers no solution? Our support team searches for useful product information and answers to frequently asked questions.
If you find an inaccuracy in our frequently asked questions, please let us know by using our contact form.
JavaScript disabled. Without JavaScript our website won't work properly. This will avoid abnormal noise and rise the durability of the motorcycle. Page Wiring Diagram. Remove the six screws on the back of the front cover. Remove the front cover. The installation sequence is the reverse of removal. Remove the met-in box. Cover The installation sequence is the reverse of remove Remove the three bolts attaching each of the right and left side covers. Remove the ignition switch decorative ring Remove the leg shield.
Page Maintenance Schedule. Page Fuel Filter. Page Air Cleaner. Remove the air cleaner element by removing the four screws. Check the element and replace it if it is excessively dirty or damaged.
Page Valve Clearance. Remove the frame cover. Remove the cylinder head cover. Page Ignition Timing. Check the ignition timing with a timing light. Page Agility. Stop the engine and remove the oil check bolt. The oil level shall be at the oil check bolt hole. Page Brake Shoe. Refer to page and for brake shoe replacement. Page Headlight Aim. Turn on the headlight switch. Check the entire shock absorber assembly for oil leaks, looseness or damage. Jack the rear wheel off the ground and move the rear wheel sideways with force to see if the engine hanger bushings are worn.
Raise the front wheel off the ground and check that the steering handlebar rotates freely. If the handlebar moves unevenly, binds, or has vertical movement, adjust the steering head bearing. Page Lubrication System. Right Crankcase Cover Remove the gasket and dowel pins. Disassembly the oil pump. Service Limit: 0. Torque: 0. Page Fuel System. Page Service Information. Page Troubleshooting. Page Carburetor Removal.
Wait 5 minutes and blow the hose with mouth or vacuum pump. Page Air Cut-Off Valve. Remove the spring and vacuum diaphragm. Check the vacuum diaphragm for cracks or damage and check each passage for clogging.
Air Cut-off Valve Cover Inspect the vacuum piston for wear or damage. Inspect the diaphragm for deterioration and tears. Page Float Chamber. Remove the float pin, float and float valve.
Float Pin Needle Jet Holder Inspect the float valve and valve seat contact area for stepped wear or contamination. Page Carburetor Installation. Install the carburetor onto the intake manifold, aligning the tab on the carburetor with the cutout in the intake manifold. Page Pilot Screw Adjustment. During carburetor disassembly, note the number of turns of the pilot screw and use as a reference when reinstalling it.
Page Fuel Tank. Remove the frame body cover. Page Fuel Unit. Disconnect the fuel unit wire connector. Turn the fixed plate on the fuel unit,take the fuel unit off. Page 69 6. Be careful not to damage the motorcycle body, cables and wires during engine removal. Disconnect the engine negative cable. Disconnect the spark plug high tension wire. Disconnect the auto bystarter wire connector. Page 71 6. Remove the rear brake adjusting nut, connecting pin and rear brake cable.
Engine Mounting Bolt Remove the four A. Install the engine hanger bracket bolt and tighten the nut. Page 74 7. Page 76 7. Remove the four cylinder head cover bolts to remove the cylinder head cover. Remove the two nuts attaching the secondary air inlet tube. O-ring Remove the cam chain tensioner cap screw and the O-ring. Remove the four cylinder head nuts and washers. Washer Camshaft Holder Remove the camshaft holder and dowel pins. Page 78 7. Replace the camshaft assembly with a new one if the bearings are noisy or have excessive play.
Remove the carburetor. Remove the exhaust muffler. Remove the carburetor intake manifold. Remove the cooling fan cover. Remove the engine cover bolts and screws. Separate the engine cover joint claws. Page 80 7. Check valve movement in the guide. Measure each valve stem O.
Service Limits: IN : 4. Page 82 7. Page Camshaft Installation. An example of data being processed may be a unique identifier stored in a cookie. Some of our partners may process your data as a part of their legitimate business interest without asking for consent. To view the purposes they believe they have legitimate interest for, or to object to this data processing use the vendor list link below.
The consent submitted will only be used for data processing originating from this website. If you would like to change your settings or withdraw consent at any time, the link to do so is in our privacy policy accessible from our home page.. Manage Settings Continue with Recommended Cookies. Vendor List Privacy Policy.
Comments
Post a Comment